Nokia 101 Full PCB Diagram Mother Board Layout

Nokia 101 Full PCB cellphone Diagram Mother Board Layout.
Here is the cellphone diagram of Nokia 101 PCB.so i will add some more cellphone diagram in high resolution so that you can add some more repairing trick for

Nokia 101 Mic Problem Jumpers Ways Solution

If nokia 101 mic is not working or sending low voice to the destination then you can solve mic problem with these few steps that are given bellow in diagram. look at the diagram and do following steps step by step.

In pictures you can see two main colors blue and red these colors are identifying outer and inner points of mic.outer is a ground point of mic while inner is a + point of mic. remove the old mic from board and then check the path as shown in diagram jumper new mic with these parts and if parts are also broken due to water damage then big round points are identifying locations where you can apply jumper and these are test points for mic problem in nokia 101, see some points can also be scratched. So scratch them slightly and make jumper at that point.

Nokia 101 MMC Memory Card Problem Solution

If you are facing mmc problem in nokia 101 then here is a helpful and useful diagram for you to solve these problems.loock at diagram bellow and in it you can see an ic is identified with red box. This part is used for memory card functions in nokia 101.

Check all the board carefully and if there is some rust carbon or water damage then clean it with electronics cleaner and dry it with hot air or put it under electrical bulb for a few mint so that can be dry. not apply to much heat because and can be harm for your mobile circuit.
Then resold this ic with hot air and if not solve the problem then change this.

Nokia 101 Network problem single solution ways

If in nokia 101 you have no network problem low signals problem then you can solve this problem with a few steps as shown in diagram bellow. look at the diagram and see all path and lines are defining ways of network signal function in nokia 101.

In diagram red lines show network path and blue line show antenna path. first of all check antenna is not broken and its points are in good condition and not water damaged or carbon is not on them. then make jumper on antenna as shown in diagram so that if it is discontinued then can be in normal flow.
Then heck red lines and red box parts and resold them with hot air so that if any of them is not showing continuity then can be in normal flow and pass the signals.

Nokia 101 not charging problem solution ways

Nokia 101 not charging fake charging can be solve with a few steps that are describe in this post. so look at the diagram bellow and follow steps given in image.

As in all nokia sets charging points are two and one of them is ground and other is +v.in it a red line is identifying path of voltage that pass through these parts. so if link is broken then make jumper and check these parts and resold them or replace them.
Coil , resistance, and charging ic can be remove and you can apply direct jumper to the capacitor. Capacitor have on side ground while other side is +v.

Nokia 101 Ringer Speaker Problem Ways Solution Jumpers

If ringer or speaker is not working in nokia 101 or you are facing low voice or bad quality in it then this diagram will help you to understand the problem and solve it. check diagram given bellow and follow steps that are shown in it.

In diagram you can see parrot and pink colors that are identifying ringer and speaker path. so check these paths with Multi Miter and if any of them is broken then make jumpers as shown in diagram above. a big round point shows here you can make jumper and these are test points for ringer speaker problem. low ringer, low speaker.

Nokia 101 LCD Blank Display Ways Jumpers Problem Solution.

Nokia 101 lcd problem,white display problem,blank display and no light in lcd display of nokia 101 can be solve with a few steps that are given in this post bellow is the diagram of nokia 101 to solve lcd problem in it.

In diagram above you can see there are different color lines and these are identifying the path of lcd prints.lcd pins are counted in picture from left to right as 1,2…12 and these prints can be check with a multi meter if any of them is broken or any component is broken you can make jumper to the points that are shown in picture and a big round point shows here you can make jumper and these are test points for lcd display blank display problems.
As in lcd points numbers are shown same numbers are defined with parts so that you can easily find where you have to apply jumpers. . if any part is not at the same place and have broken due to water damage or something else then you can see some points can also be scratched. So scratch them slightly and make jumper at that point.

Nokia 101 Insert Sim Problem Solution Jumpers Ways

Nokia 101 have two stand by sims in it.if you are facing insert sim problem in nokia 101 for both sims or a single sim is not working here is the diagram that will help you to solve this problem in nokia 101.

In diagram you can see there are multiple lines with different colors that are indicating different sim points and there path to different parts you can check these path and if any of them is broken then you can make jumpers to them. if any part is not at the same place and have broken due to water damage or something else then you can see some points can also be scratched. So scratch them slightly and make jumper at that point.
Big round points on lines shows that you can make jumper on that point.

Nokia 101 Dead and Not switch On with Battery

If you have a Nokia 101 Dead problem and it can not be switch on power on with battery but can be on with dc power supply then you can try this solution. look at the diagram given bellow in this post.

You can see two red box in picture one of them is showing text remove so remove that resistance and other one you have to replace. check battery terminals also because in some cases it can be water damage or carbon on it.
So if you see some carbon or rust then clean the board and battery terminals with electronics cleaner and dry for a few mints with hot air or under electrical bulb.